Archive for  
 

Technical Questions
Click here to go to the original forum
Page 1, 2, 3, 4, 5, 6, 7, 8  Next
 
 Topics 
Why are there no modern replacement oil lines out there?
h2b 3 into 1 oil line
Bigger better?
Kh 500 running problem
Oil check valves
r/h front disc pipe
Kh400 clutch
Kh250 pilot jets broken
2nd disc conversion
Cleaning out cylinders after a rebore.
Seat logo
Houston....we may well have a problem
A problem that I can`t seem to solve
oil banjo crankcase
Gearbox shimming
Any idea what these fit ?
smoking on r/h cylinder on h2b
Cylinder head orientation KH 250
S2 Kickstart ball bearing spring
Connections for Simon's regulator/rectifier for S1
To choke or not to choke ?
Bolts - - number 4 or 7 ?
releasing brake piston out of caliper, whats the trick?
what parts do i need for adding a 2nd disc to h2b
Wont fire up after carb and tank clean
leaking clutch atuator
Crankcase banjo washers
Won't pull away
1972 S2
new regulator/rectifier or not
H1B question
Electrical bits and bobs kit
Bit of a Problem
KH400 clutch identification.
Points & Paint
KH250 battery - which to choose?
paint code wanted
Repro left handbar switch for S3 - the one with the choke on
Condensers - 1 wire or 2?
Exhaust port size
Electrical problem on kh500 US model
S3 oil pump banjo snapped - Advice needed
77 KH400 not charging
Heatshrink sleeve, what size for wiring loom
squealing front disc brake
KH500 regulator -. Brown wire?
KH400 A4 won't switch off.
Wiring help
Fuel Tap Leak
loud rattling from clutch casing on h2b
Footrest Bolt
S2 rear indicator mounting
Advice needed please re KH250 B4 combined reg/rec fitting
Engine building.
leak down test
Cleaning up black plastic
All me bits are worn out. Also, hello!
Horn rebuild - gaskets?
Offset Sprocket
parking light us model
Barrels re bore
S3A CLUTCH
S3A points cover question
Chroming fork stanchion
fuel starvation
Rear shocks
VM26SC S3 carbs on a S2 ?
KH400 HT Leads removal
KN filter for genuine S1 S2 airbox ??
Reboring S1 Cylinders to S2 diameter
Speedo numbers aligning
S2a final drive ratios
S3A charging fault.
Center distances 1972 S1/S2 forks and next S series
S2a rear hugger
Converting to synthetic 2t
asco master cylinder
Stripping down shock KH250
Carb idle
B5 engine casings
Little beauty
Wheel/Hub offset KH250 front and rear
clutch cable length
Boyer Bransden mk3 ignition advance
kh400 motor fits into KH250 ?
S2heads Numbers meaning ???
2 stroke oil lines
Welding engine cases-maybe one for Roger?
metal bond for repairing exhaust, which do i need?
KH400 - seat dimension question
Loose carbs
Clutch plate wavey springs
250 exhaurst
Leaking left hand casing, O ring on shaft?
Centre cylinder
Oil pump swap
Ticking noise kh400
KH250 Clutch rods length problem?
Centre cylinder
Sr ignition switch
Lumiweld
Top yoke pinch bolt
kh250 rotor/points whats going on here?
Needle valve
S series conrod centres
2/4 seat
fork seal leaking
Oil pump rubber washers
kh250 rear bolts that hold the chrome bumper to frame
critical float heights
Spark plugs
Help getting bike running
Clutch
Oil tank sight glass leak
KH250 running rough at low RPM
Primary gear O-ring
Left hand switchgear repair?
s3 spark plugs
Does anyone know the make of these exhaust!?
Parts recognition please ?
KH400 oil leak
S2A Fork Spacers
KH250 Carb Question - Brass Stub
Kh250 baffles query
Brake light query
Carb bits
Starting up problem 250 b5
Low speed coil?
1982 Perspex reg plate font
Kh500 neutral light problem
Bike Starts Without Choke
Oil pump feed adjustment
KH400 gear change oil seal
Oil pump feed pipe
Balancing the carbs
Horn
H2B/C Engine Case Check Valves
Electrics completely dead on S3
KH250 special
Drum brake
H2A and H2C
Indicators
RPM question
Repair stripped thread in ally tank - advice please !
KH 400 Carb leak
kh400 routing of stator and CDI wiring.
Carb kits
Master Cylinder Blocked hole
ARE spacer.
electrics and cable routing
KH250 B3 Blue Paint Code
LIGHTS ON ENGINE DIPS
Kh250 piston
Spoke Prep for Zn Plating
S2 carbs
Decals for 500- where to put them?
Ignition.
Motor assembly and oil
ignition
Led indicator
Headstock decal
KH250 engine mounting bolts
Taking apart if possible
KH400 - free ignition testing guide
KH - Higher bars
Kick Start Ball bearing removal
kh 400 not running on all three
Repairing silencers
fuel tap on S3
KH500 cutch drag
mystery object in float bowl
Electric drill on the oil pump
Wiring loom
Foot rest holder kh250
Engine case thread stripped
Flat black ?
LC 350 engine studs
Big end or small end noise
Oil pump.....drip,drip,drip
Excessive smoking, should i be bothered
Leaking kh500 carb
Metal grade for steering stem
Part throttle miss
Swapping steering stems and yokes
crankcase bearing pins
Kh250 brake pipes
KH400 Center Stand
Carb wear?
KH250 top end swap.
KH400 centre piston seizure
Broken wire
rev counter / carbs
2stroke consumption
Kh250 seat lock
S2 /kh400 carb inlet manifold
Float Valve
KH250 speedo and Rev clock testing
Tyre Pressures - KH 250 ?
Speedo and tacho rebuilds
S2a going to put dencos on....jetting?
 
Page 1, 2, 3, 4, 5, 6, 7, 8  Next
Page 1 of 8